How to Check glue level

Back in May, I neglected to replace the glue cartridge when replacing the rest of the material kit and ruined a model because the SD300 ran out of glue during the next build. Since then I've tried to always replace the glue cartridge in sync with the PVC roll.

I learned to double-check the glue cartridge's capacity by shining a high-intensity LED flashlight through the side walls, which reveals the glue level as a bright line on the wall.

Today I was startled to discover the glue cartridge was essentially empty, even though there was plenty of PVC left in the material kit. There should've been plenty of glue left. Notice the bright line is all the way at the bottom.


I still had the glue cartridges from two recently-exhausted material kits. There was a little glue left in one of them, but that's how much is usually left over after a kit has been used up. The bright line is near the bottom.


When I checked the other "empty" cartridge the LED light showed it had a lot of glue left in it. Notice how the bright area is well above the bottom!


Probably I got an 'empty' cartridge swapped with a non-empty one when changing between colors recently. I shouldn't leave the empties nearby. It's fortunate I discovered it before the machine completely ran out of glue.

Improved transparency for the Cooksey Tribute puzzle

EDIT: Just to clarify, I only built the transparent rings in the pictures. The brightly-colored maze cylinders were purchased from Oskar's store at Shapeways.

In a previous post I described how I'd made transparent rings for Oskar's Cooksey Tribute maze puzzles. The transparency enhanced the puzzle, but they were only semi-transparent at best.


I had sprayed the previous parts with Weld-On 2007 to improve their transparency, but I soaked a second set in the solvent for 25 seconds and then permitted it to air-dry for an hour. The results were substantially more transparent.


There's some optical distortion where build chatter has been transformed into wavy lenses, but the new part is more transparent.


So now I'm building a new set of enhanced transparent rings using the solvent soak-dip.


I had discovered the value of a solvent dip long ago, but I'd been using a simpler solvent-spray to make it more convenient. The dip requires a relatively large volume of Weld-On 2007 welding solvent, a solvent-resistant surface, gloves, and ample ventilation. But these results are worth some special effort!

There are additional pictures of Oskar's Cooksey Tribute in my PhotoBucket Album.

Rox shares the Rox Box with Uwe Mèffert

In August I built a gem-filled puzzle for a widely-known puzzle collector, Roxanne, and named it the Rox Box in her honor. It featured two puzzle-engraved gem stones locked behind clear windows, and the box could only be opened by navigating the lid through a maze in the shape of the word "Rox," Roxanne's nickname. I built only one, so she owns a very exclusive specimen.


Recently Roxanne met Uwe Mèffert over dinner in Hong Kong. Mèffert invented the Pyraminx puzzle, which was popular back in the Rubik's Cube puzzle craze in the 1980s. He still develops and sells puzzles at his web store www.mefferts.com

Roxanne showed him her Rox Box puzzle and kindly sent me a picture of Mèffert playing with it. He praised the way it incorporated her name right into the puzzle!


Mèffert showed some of the puzzles he's developing for his store, and Roxanne shared many of the favorites in her own collection. I'm very flattered she included the Rox Box because I interpret her choice as a sincere expression of appreciation. I'm grateful for that!

Faking a power outage

Yesterday I noticed the SD300 had mysteriously stopped part way through a build. The computer's status monitor said the SD300 was actively building layer 22, but the SD300's display suggested it was waiting for the computer. Pressing Pause/Resume had no effect.


So I ran the SDView, the SD300 maintenance app, and brought up the machine's log. There were 3 unusual entries that said "Unknown command in file." Had there been a data transmission error between the computer and the SD300? In any case, the log indicated the SD300 hadn't finished layer 21 because it was "waiting for host" to send the last data, but I guess the computer thought layer 21 had been finished and was waiting to send layer 22. Stalemate!


So, how could I resolve this apparent deadlock?

The SD300 has a robust procedure for recovering from power outages, so I pulled the plug for a few minutes to simulate a power outage. That worked!

When I plugged it in again, the SD300 went through its initialization and recognized that it had unfinished model. After verifying the model's integrity the SD300 asked me to confirm that it should resume the model in-progress. Sure enough, it negotiated with the computer to re-load the model data and it resumed building after a 2 minute pause for "Loading."

Using a Pin Vise to clear small holes

For a while I disliked building parts with deep, narrow holes because leftover support material clings tenaciously inside the holes and solidly blocks them. There's common advice to simply clear the holes with a drill, not my favorite solution.

A colleague suggested using an ordinary drill bit in a pin vise. The pin vise allows the bit to be twirled freely, and the handle provides leverage and strength.



Because its a handheld tool, the pin vise gives tactile feedback that makes it easy to guide the bit to follow the intended path of the hole. I found it helps to run a peeling cut down the middle of the hole, which gives the flutes a loose edge to grab onto.


Surprisingly, the manually-operated drill bit clears away leftover material very quickly yet doesn't tend to cut into the model itself. The model is quickly cleaned up by scraping the drill bit against the sidewalls and withdrawing it to clean the flutes.

George Bell's Exploding Ball

Yesterday designer George Bell emailed me a file for his Exploding Ball puzzle. The pieces have all sorts of awkward angles, so I just took a guess on how to orient it for optimal building on the SD300.

It would take about 7 hours to build all eleven parts, but I chose to build 3 sample parts because it would only take 3 hours so I'd be able to inspect them before bedtime. It was lucky that I'd printed a couple of samples, as I'd arranged the peeling cuts so they put stress on a thin section. I broke one of the pieces when I hastily peeled the supports away. It wouldn't impair the part's usefulness, but it's unsightly. (Clarification: The part on the right is flat where a tiny piece of the curve broke off; the part on the left is intact, showing how the curve should look.)


I fixed the peeling cuts and ran another build overnight. Today I peeled away the supports quickly, easily, without any damage to the parts. When the parts are assembled, they form a ball that's virtually impossible to disassemble because of the smooth surface and bizarre angles. Even if you get your nails in the cracks you can't pull it apart because your touch tends to hold the puzzle together. But it's supposed to disassemble when it's spun, thanks to centrifugal force.


It took me half an hour to assemble the puzzle the first time, so I recorded a video of my first attempt to 'explode' the puzzle because I wasn't sure if I'd get it put together again. It took several tries. It's lucky the finished model is pretty tough, since I dropped it at lot!

Cooksey Maze

In the 1970s Richard Cooksey invented a cylindrical maze puzzle, which underwent some development by Pentangle Puzzles & Games but didn't ultimately become a commercial product. Puzzle inventor Oskar van Deventer recently adapted the puzzle and made it available through Shapeways as Cooksey Maze.

Oskar also designed a series of six Cooksey Tribute puzzles, each a different variation on the basic concept.


The ring has two pins that ride in the grooves on the cylinder; it's shaped so the user can choose one pin to lift out of the grooves, permitting the user to switch from one side of the 'maze' to the other. The ring is attractively cut with large openings for the user to look through, but the opaque material undesirably blocks the view of the maze. Oskar said he would have preferred to make the rings transparent, so I offered to try building a set on the SD300.


I built a complete set of six rings, corresponding to the six variants of Cooksey Trubute, using the amber-transparent material. The 3-4mm thick sidewalls aren't crystal clear, but they're sufficiently transparent to give a clear view of objects inside.


Sure enough! The transparent rings give a clear enough view to permit the puzzle to be explored and solved pleasantly.


M. Oskar van Deventer is offering a free Cooksey Maze to anyone who can put him into contact with Mr. Richard Cooksey.

Multi-color build

I've used clear & opaque material in the same build, so now I tried building with two colors in the same build. Part way through this build I replaced the white material kit with black, resulting in a model block that resembles an Oreo cookie.


The finished parts show a nice, distinct transition from one color to the other.


I assembled the parts into a puzzle and added colored tiles. It looks a bit bizarre, but it shows how two colors can be used together.

Cubic trisections

A few days ago I explored many novel ways to trisect a cube into three identical parts. Could they be adapted into a puzzle? To find out I printed three samples, each using different parameters.


Each cube is made of 3 identical parts, which slide together (or apart) with a novel twisting action.


Here are the individual pieces of one trisected cube.


Because the model included some spots as thin as 0.3 mm I chose the build orientation carefully to exploit the SD300's ability to build thin layers in the Z axis.


Light reflects and refracts spectacularly inside each model. I don't regard it as a finished puzzle, but the SD300 encouraged me to try out an idea I might have ignored.

Rox Box: Clear and opaque in the same parts

I built this puzzle box for a collector named Roxanne, and incorporated her nickname "Rox" into the puzzle itself. The box holds the gemstones using the gem holders I built earlier, so I called it the "Rox Box."


The gem holders slide into a plastic insert, which corkscrews into the middle of the puzzle box. Rox's nickname is carved into the walls, which creates a maze the lid has to be threaded through to open the box. This premise was inspired by Teifenbacher's A-Mazing Box at Thingiverse.


It's 3D printed with a combination of opaque materials and clear material to form windows, so the gems are visible when the box is closed. A ruby is visible through the top, engraved with a Rubik's Cube.


A sapphire is visible through the bottom of the box.


To build opaque parts with clear windows I switched between transparent and opaque material while the SD300 was building, which resulted in a seamless transition between the two. Thus the clear windows are integral, rather than being assembled separately.


This was my first attempt to combine two materials, and it worked perfectly on my first try! In this instance I simply arranged the parts so the window would be built first, and started building with clear material. When it had built to a height of 2mm (the thickness of the windows) I selected "Unfeed media" on the front panel, swapped-in the opaque white material, and let it continue building.

Gem Holders

Last year I learned to engrave little pictures onto various gemstones using a CO2 laser. I got the best results from lab-grown rubies and sapphires (both corundum) which etched to a frosty image that contrasted nicely with the saturated color of the stones.

I wanted to share the engraved gemstones with other puzzle enthusiasts but the loose stones are easily lost, so I designed and built gem holders on the SD300 using black material.


The flexible tabs allow the gem to be snapped securely into place. Each gem can be removed by pushing it out of the holder through a cavity in the back.


I also built a gem holder using transparent material, which slips into an opaque white holder.

Reditt model

I stumbled upon a model of a cute little robot called Reditt. I was intrigued by the thin, angular antenna atop his head. It's only about 1mm thick, but I was sure the SD300 should could build it because the antenna lies entirely within a single plane and the thick ball would prevent any loose ends.


I built the model lying down, so the antenna would be completely horizontal. Here's the completed model block with the robot's face smiling from within the support material.


I had arranged the peeling cuts so the material could be peeled away from one side of the antenna at a time.


I peeled one section at-a-time from the end of the antenna to the robot's head until the whole antenna was free.


I built a pair of robots, using amber-transparent and opaque cream plastic. The antenna looks delicate, but it's surprisingly robust. One survived unblemished after being dropped on a concrete floor.


The transparent model looks spectacular standing on a Oscillating LED Light Stand I bought from American Science and Surplus for $2.95.

Mizzing Piece "Test Part" puzzle

The SD300 has a built-in capability to build an functional Test Part using a minimum of consumables (less than $3 of total materials) which can be folded and snapped together into a neat little pyramid. Most users probably accumulate plenty of these parts from testing the printer after cleaning, servicing, and routine operations.


I've watched friends and guests toying with these little pyramids. Often, they try to stack them to form a larger pyramid, but it just doesn't work.

It occurred to me to design a simple part that can be combined with the test parts to build a larger pyramid, like the one pictured below. It's sort of like a "missing piece" for the larger pyramid.


In fact, my extra piece looks just like the standard test part...at first glance. It's foldable sheet of four triangles, like the test part, but the edges are chamfered at different angles and there are other differences.


This shape forms very-narrow channels during printing, which has the disadvantage of leaving hair-thin strands of support material that must be peeled away. I've successfully cleared the waste material from every part I built so far, but it takes a bit more effort than usual!


I added a triangular hole to the new part to help distinguish it from the ordinary test parts. As shown here, it doesn't quite fold like the regular test part.


I soon found the hole was a convenient feature to help disassemble the parts, so I designed a version of the standard SD300 Test Part with a round hole to reach inside and pop it apart. A complete puzzle set consists of one Mizzing Piece part (triangular hole, at right) and five standard test parts or my equivalent (round holes, at left).


I posted the Mizzing Piece STL at Thingiverse