Too thin?

Yesterday I encountered a puzzle designer who'd shared a rough draft of a model with impractical, thin walls. The pictured model is only 19mm high, with many 0.63mm walls and several tapers that were even thinner.

I'd tried to avoid thin walls in my earliest designs for the SD300, but occasionally built thinner walls by chance or miscalculation. Some worked, some didn't, but I always learned something new. So I got permission to build the model, fully aware I was going to have problem with it.


Unsurprisingly, lots of really thin areas broke away while removing the supports. I managed to preserve some walls as thin as 0.5mm by peeling the support material away slowly, one layer at a time. Some undercuts were so narrow I couldn't even reach into them with my curved forceps.


Still, the model emerged sufficiently intact for examination. The channel walls were so thin I could barely get a fingernail inside, and they were noticeably flexible. I dipped the parts in Weld-On 2007, which immensely strengthened the surviving structures.


Surprisingly, the parts can be assembled...barely! The tolerances were inadequate, but they just barely functioned because the channel wall flexes just enough to compensate.


The design doesn't make provision for installing all four parts, so I couldn't assemble the whole puzzle. But it's impressive that it worked at all.


These parts aren't practical due to the overly-tight tolerances, but the model confirms the designer's concept nevertheless. But I certainly wouldn't try to build such thin walls routinely. A comparable model might take 10 minutes to clean away the supports, while this took almost 2 hours. If it hadn't been for the Weld-On dip the parts probably would've broken during testing.

But it shows that the user can venture outside of "good practices" at his discretion. The SD300 will attempt to build any geometry it can process, even if it's not practical. It's the user's choice.

How to Check glue level

Back in May, I neglected to replace the glue cartridge when replacing the rest of the material kit and ruined a model because the SD300 ran out of glue during the next build. Since then I've tried to always replace the glue cartridge in sync with the PVC roll.

I learned to double-check the glue cartridge's capacity by shining a high-intensity LED flashlight through the side walls, which reveals the glue level as a bright line on the wall.

Today I was startled to discover the glue cartridge was essentially empty, even though there was plenty of PVC left in the material kit. There should've been plenty of glue left. Notice the bright line is all the way at the bottom.


I still had the glue cartridges from two recently-exhausted material kits. There was a little glue left in one of them, but that's how much is usually left over after a kit has been used up. The bright line is near the bottom.


When I checked the other "empty" cartridge the LED light showed it had a lot of glue left in it. Notice how the bright area is well above the bottom!


Probably I got an 'empty' cartridge swapped with a non-empty one when changing between colors recently. I shouldn't leave the empties nearby. It's fortunate I discovered it before the machine completely ran out of glue.

Improved transparency for the Cooksey Tribute puzzle

EDIT: Just to clarify, I only built the transparent rings in the pictures. The brightly-colored maze cylinders were purchased from Oskar's store at Shapeways.

In a previous post I described how I'd made transparent rings for Oskar's Cooksey Tribute maze puzzles. The transparency enhanced the puzzle, but they were only semi-transparent at best.


I had sprayed the previous parts with Weld-On 2007 to improve their transparency, but I soaked a second set in the solvent for 25 seconds and then permitted it to air-dry for an hour. The results were substantially more transparent.


There's some optical distortion where build chatter has been transformed into wavy lenses, but the new part is more transparent.


So now I'm building a new set of enhanced transparent rings using the solvent soak-dip.


I had discovered the value of a solvent dip long ago, but I'd been using a simpler solvent-spray to make it more convenient. The dip requires a relatively large volume of Weld-On 2007 welding solvent, a solvent-resistant surface, gloves, and ample ventilation. But these results are worth some special effort!

There are additional pictures of Oskar's Cooksey Tribute in my PhotoBucket Album.

Rox shares the Rox Box with Uwe Mèffert

In August I built a gem-filled puzzle for a widely-known puzzle collector, Roxanne, and named it the Rox Box in her honor. It featured two puzzle-engraved gem stones locked behind clear windows, and the box could only be opened by navigating the lid through a maze in the shape of the word "Rox," Roxanne's nickname. I built only one, so she owns a very exclusive specimen.


Recently Roxanne met Uwe Mèffert over dinner in Hong Kong. Mèffert invented the Pyraminx puzzle, which was popular back in the Rubik's Cube puzzle craze in the 1980s. He still develops and sells puzzles at his web store www.mefferts.com

Roxanne showed him her Rox Box puzzle and kindly sent me a picture of Mèffert playing with it. He praised the way it incorporated her name right into the puzzle!


Mèffert showed some of the puzzles he's developing for his store, and Roxanne shared many of the favorites in her own collection. I'm very flattered she included the Rox Box because I interpret her choice as a sincere expression of appreciation. I'm grateful for that!

Faking a power outage

Yesterday I noticed the SD300 had mysteriously stopped part way through a build. The computer's status monitor said the SD300 was actively building layer 22, but the SD300's display suggested it was waiting for the computer. Pressing Pause/Resume had no effect.


So I ran the SDView, the SD300 maintenance app, and brought up the machine's log. There were 3 unusual entries that said "Unknown command in file." Had there been a data transmission error between the computer and the SD300? In any case, the log indicated the SD300 hadn't finished layer 21 because it was "waiting for host" to send the last data, but I guess the computer thought layer 21 had been finished and was waiting to send layer 22. Stalemate!


So, how could I resolve this apparent deadlock?

The SD300 has a robust procedure for recovering from power outages, so I pulled the plug for a few minutes to simulate a power outage. That worked!

When I plugged it in again, the SD300 went through its initialization and recognized that it had unfinished model. After verifying the model's integrity the SD300 asked me to confirm that it should resume the model in-progress. Sure enough, it negotiated with the computer to re-load the model data and it resumed building after a 2 minute pause for "Loading."

Using a Pin Vise to clear small holes

For a while I disliked building parts with deep, narrow holes because leftover support material clings tenaciously inside the holes and solidly blocks them. There's common advice to simply clear the holes with a drill, not my favorite solution.

A colleague suggested using an ordinary drill bit in a pin vise. The pin vise allows the bit to be twirled freely, and the handle provides leverage and strength.



Because its a handheld tool, the pin vise gives tactile feedback that makes it easy to guide the bit to follow the intended path of the hole. I found it helps to run a peeling cut down the middle of the hole, which gives the flutes a loose edge to grab onto.


Surprisingly, the manually-operated drill bit clears away leftover material very quickly yet doesn't tend to cut into the model itself. The model is quickly cleaned up by scraping the drill bit against the sidewalls and withdrawing it to clean the flutes.

George Bell's Exploding Ball

Yesterday designer George Bell emailed me a file for his Exploding Ball puzzle. The pieces have all sorts of awkward angles, so I just took a guess on how to orient it for optimal building on the SD300.

It would take about 7 hours to build all eleven parts, but I chose to build 3 sample parts because it would only take 3 hours so I'd be able to inspect them before bedtime. It was lucky that I'd printed a couple of samples, as I'd arranged the peeling cuts so they put stress on a thin section. I broke one of the pieces when I hastily peeled the supports away. It wouldn't impair the part's usefulness, but it's unsightly. (Clarification: The part on the right is flat where a tiny piece of the curve broke off; the part on the left is intact, showing how the curve should look.)


I fixed the peeling cuts and ran another build overnight. Today I peeled away the supports quickly, easily, without any damage to the parts. When the parts are assembled, they form a ball that's virtually impossible to disassemble because of the smooth surface and bizarre angles. Even if you get your nails in the cracks you can't pull it apart because your touch tends to hold the puzzle together. But it's supposed to disassemble when it's spun, thanks to centrifugal force.


It took me half an hour to assemble the puzzle the first time, so I recorded a video of my first attempt to 'explode' the puzzle because I wasn't sure if I'd get it put together again. It took several tries. It's lucky the finished model is pretty tough, since I dropped it at lot!